1957 Ford Ranchero Gets Modified Stainless Trim

By Brian Limberg – Photography By NotStock Photography & Tin Man’s Garage
Artwork by Jimmy Smith Concepts
The 1957 Ranchero body was derived from a basic station wagon. Specific roof sections on the quarter-panels were cut off, and other trim pieces were stamped to cap voids and conceal areas of the original body make. The modified stainless trim for this Ranchero’s bed was designed to cover the remnants of window tracks for the side windows and back glass. Most of these modifications were crude, to say the least, and the final fitment was of little concern or value.

It isn’t uncommon for major automotive manufacturers to “Frankenstein” or modify standard make-and-model vehicles to create new models. Not having to build separate stamping tooling typically saves time, which saves money.

Rear three-quarter angle of a custom bare-metal 1957 Ford Ranchero showcasing grafted taillight housings and custom bed trim at dusk.
It’s always very cool and informative to see a hot rod before final bodywork and paint. Here, this moody nighttime scene makes the 1957 Ford Ranchero appear ready to roll—Cool Ranch.

Mike Long, the owner of this 1957 Ford Ranchero, presented the idea of making modified stainless trim to fit better rather than removing the seams and screw holes after being reminded of how poorly they fit and seeing an all-original, restored Ranchero at a car show. With numerous modifications made to this specific build to clean up the original factory design, Tin Man’s Garage dove headfirst into this project with a simple yet somehow complex process. MR

Check out this story in our digital edition here.

Side-profile rendering of a custom 1957 Ford Ranchero by Tin Man's Garage with callouts for 6061 aluminum side trim and body modifications.
If you have followed along, you can see what artist Jimmy Smith had in mind after listening to both Mike Long, the owner, and Brian Limberg of Tin Man’s Garage. And it’s coming together nicely.

 

Elevated view into the bare-metal bed of a 1957 Ford Ranchero highlighting modified fluted bed rail trim and a one-piece rear window opening.
Here is your goal with new, modified stainless trim in place.

 

Pair of factory ribbed stainless steel bed rail moldings laid out on a truck bed floor before custom modification.
The process began by filling all the screw holes in the trim, which yielded the modified stainless trim. The recessed holes were flattened, and small, stainless steel sheet metal plugs were punched. The plugs were TIG welded in place, then carefully sanded and metal finished one by one.

 

Curved fluted stainless trim clamped to a welding table with green tape and tack welds aligning a custom butt joint.
The stepped flanged edges were trimmed, and the trim was clamped into its proper position on the body. Specialized dollies with caulking tools were used to make minor adjustments to prepare the fitment for tack welding.

 

Close-up of a full-penetration TIG weld joining two sections of ribbed stainless steel trim alongside filler rod on a metal table.
After the trim was tack welded, the seams were fully welded. The primary concern when welding thin modified stainless trim is to minimize heat to limit undercutting into the base metal, which makes metal finishing more difficult because it requires going back and adding weld to fill low voids.

 

Dura-Block sanding block, body hammer, and layout dye used to smooth and reshape a welded stainless trim seam.
Each weld seam was sanded with an 80-grit Roloc-backed disc on a 90-degree pneumatic die grinder and then blocked by hand. The lows were picked up, the highs were hammered down, and the seam was block sanded repeatedly.

 

Smooth, sanded ribbed stainless steel trim strip resting on a fabrication bench with its welded joint blended invisibly.
The process continued along each of the ribs until the weld seams disappeared. This is an example of how the trim looks after the weld seams and the filled holes were metal finished.

 

Macro end-profile view of thick CNC-machined 6061 billet aluminum side trim fitted to a 1957 Ford Ranchero door edge.
The ends of the modified stainless trim were trimmed and then extended or shortened as needed. New flanged ends were cut and formed to fit. The flanges were corner welded and metal finished.

 

Close-up of modified fluted stainless steel trim meeting at the rear corner joint of a bare-metal 1957 Ford Ranchero bed.
Replacing the flanged edges allowed the gaps to be corrected and made consistent with the adjacent trim. Additional work was previously done to rework the top of the tailgate to improve the beltline detail running under the trim, resulting in a more consistent fit.

 

Macro view of a TIG-welded rectangular mounting pocket with a drilled stud hole inside a bare-metal tailgate frame.
Small pans were fabricated with new mounting holes. These recessed pans were placed around the perimeter of the trim at appropriate locations with backside access to install a washer and a nylon nut.

 

Backside of a fluted stainless steel trim molding showing a welded steel plate and threaded stud aligned with a body pocket.
These large threaded stud plates help distribute the drawing force when tightening the nylon nut fasteners. This design reduces the draw to prevent low spots or waves in the finished trim.

 

View along the passenger-side bed rail and tailgate of a bare-metal 1957 Ford Ranchero showing custom wrap-around fluted trim.
Completed hidden fasteners installed on the passenger’s side bed trim achieve a modern, smooth look. Removing the unnecessary seams and holes also improves the original fitment and allows the gaps to be dialed in.

 

Fabricator test-fitting a primer-coated curved corner section of ribbed stainless trim along the B-pillar of a 1957 Ranchero.
The corners were originally stamped from thin sheet metal. We initially tried to rework them, however, we reached a point where we realized it would be easier to make them from scratch. Doing so would also yield better results in terms of how they fit.

 

End mill cutting parallel grooves into a steel block clamped in a milling vise to create a custom trim-forming die.
The profile was measured, and a set of male and female dies was machined from mild steel on the Bridgeport vertical mill. Proper tolerances were specified for the 18-gauge stainless steel sheet metal thickness, particularly in the vertical sections of the steps.

 

Finished CNC-milled steel forming die block held in a bench vise with smooth, rounded rib profiles.
Clearance radii are needed on the outside corners and die face to turn corners, minimizing gouges on the sheet metal’s surface finish. Hand files were used to develop the necessary details while the die was held in a vise.

 

Cast-iron benchtop metal shrinker/stretcher machine with two curved stainless steel trim blanks laid out on a steel table
Templates were created for the contours needed at the left and right corners. Additional material was added to the edges for the flanges. The ERCO Former was used to brake 5/16-inch-tall, 90-degree flanges on the inside and outside edges of the stainless steel sheet metal blanks.

 

Gloved hands guiding a curved ribbed stainless trim piece through custom billet dies in a pneumatic planishing hammer.
Two holes were drilled through the sides of the custom dies to bolt them into the universal P9 Pullmax die holders. The flanged edges served as guides to locate the trim while forming the multiple joggle (step) bead details.

 

Precision body hammer resting on a bench vise holding a custom curved ribbed trim section during final edge shaping.
A simple forming dolly was fabricated from scrap mild steel. A hammer and dolly were used to slowly form the outside edges into a 180-degree U-flange. Basic hand-forming methods are often the most efficient for small one-off parts.

 

Symmetrical pair of custom-formed curved ribbed stainless steel roof pillar moldings laid out on a metal workbench.
After the forming process, the completed trim pieces are produced. Multiple passes through the Pullmax are made with a short-stroke setting to reduce die engagement per pass. This process results in smooth parts with little to no tooling marks from stamping.

 

Custom steel forming die pressing three uniform ribs into a curved stainless steel trim piece on a hydraulic shop press.
A simple forming tool in the hydraulic shop press was used to form the corner radius. A thick-walled piece of tubing on top and a fabricated V-block on the bottom, made from scrap angle iron, worked well for making multiple small, precise movements to avoid kinking the trim while it was being formed.

 

Bare-metal 1957 Ford Ranchero cab showing custom-fitted fluted stainless steel molding surrounding the enlarged rear window opening.
The formed trim was cut to fit the surrounding trim pieces. It was tack welded at the corners with the TIG welder while in position. The majority of it was finally welded on the car before being removed for final finishing on the workbench.

 

Custom-fabricated ribbed stainless steel rear window and bed transition molding clamped together on a perforated welding table.
The inside corner flanges were formed separately and then welded in.

 

Close-up of precision TIG tack welds aligning the fluted profile across a curved corner splice on a welding fixture table.
Micro-adjustments were made to the edges to line up each section of the bead detail correctly before final welding.

 

Ground and smoothed corner radius of the custom fluted stainless steel rear window trim resting on a steel fabrication table.
The corners are painstakingly picked and sanded with small sanding blocks and files until the seams disappear. The goal was to make the modified stainless trim look as if it were stamped from a single sheet of stainless steel.

 

Passenger-side view of the bare-metal 1957 Ford Ranchero cab with seamless fluted stainless trim fitted around the back window.
Completed trim around the back window. A total of six seams were eliminated, leaving only two necessary seams for an all-new contemporary look that preserves the original vibe.

 

Rear overhead view of the bare-metal 1957 Ford Ranchero showing custom ribbed bed floor, smoothed wheel tubs, and open tailgate.
Rear overhead view of the bare-metal 1957 Ford Ranchero showing custom ribbed bed floor, smoothed wheel tubs, and open tailgate.

 

Deep midnight blue painted 1957 Ford Ranchero in final assembly with mirror-polished ribbed stainless bed trim installed.
Deep midnight blue painted 1957 Ford Ranchero in final assembly with mirror-polished ribbed stainless bed trim installed.

 

Rear three-quarter view of the completed dark blue 1957 Ford Ranchero showcasing custom machined 6061 aluminum side trim and Ranchero script.
Rear three-quarter view of the completed dark blue 1957 Ford Ranchero showcasing custom machined 6061 aluminum side trim and Ranchero script.

More from Tin Man Garage:

The John Lamb/Tin Man’s Garage Triton V10-Powered 1961 Ford Unibody

Restore Stainless Steel Trim:

How To Restore Trim Pieces On Your Classic Car


 

ITGM Source Box Heading

tin man Web Sources

Related Articles

Search Our Site