Behind The Scenes: BBT Fabrications 1967 C10

By Ron Covell

We’re going to take a look at a recent 1967 C10 project built by BBT Fabrications in Mahomet, Illinois. While the body of this truck has been left mostly stock, the detail work done under the skin is truly special, with plenty to draw inspiration from.

The condition of the truck was about as good as could be expected for something nearly 70 years old, but as you’ll see, rust had taken its toll on the cab floor and several other panels. BBT excels in sheet metal fabrication, and you’ll see them work their magic in bringing this truck back to top form.

Bare-metal custom-fabricated boxed chassis frame for a 1967 Chevy C10 resting on jack stands with suspension components nearby.
A Roadster Shop SPEC Series chassis was selected for the truck.

A Roadster Shop SPEC Series chassis was selected, engineered to accept the C10 components without modification. It includes their custom-designed and fabricated front suspension with rack-and-pinion steering, coupled with a 9-inch rear end and coilover shocks at all four corners. Roadster Shop makes a stainless steel fuel tank for this chassis, sized to tuck neatly under the rear of the bed floor with no modifications required.

A 525hp LS3 engine was selected, paired with a Bowler T56 Magnum transmission, and the BBT crew built a beautiful, all-stainless exhaust system, complete with electrically operated cutouts that exit through the bed just in front of the rear wheels.

Performance LS V8 engine with Holley EFI fuel rails and six-speed manual transmission test-fitted inside a custom 1967 C10 frame.
The LS3 engine has been fitted with vintage valve covers.

Once the cab and bed had been trial-fitted to the chassis and drivetrain, the reconstruction could begin. The entire cab floor was replaced with aftermarket panels, and new sill plates were fabricated from fresh sheet metal. The original rear cab panel was repaired and reused.

The door bottoms were badly rusted, so new metal was shaped to replace them. The inner door panels were reworked to incorporate a modern design, and the audio system speakers were recessed for a cleaner look.

All dents were smoothed out on the bed, cab, hood, and fenders, and several small, rusted areas were replaced with new metal. The metalwork was finished to perfection; it’s impossible to see where the damage once existed.

Interior cab perspective showing the completed black EDP-coated floor pan and bolted high-hump transmission tunnel in a 1967 C10.
Here the firewall and toeboard are being fitted.

Once all the fabrication work had been completed, the chassis and suspension components were powdercoated gloss black, while the underhood panels received a satin black finish.

The engine was fitted with vintage valve covers that neatly conceal the modern coil packs, and the underhood area looks exceptionally tidy.

In a future article, we’ll take a closer look at some of the underhood details that make this truck especially impressive.

Check out this story in our digital edition here.

Rear C-notch section of a custom 1967 Chevy C10 frame positioned over a notched aluminum fuel tank, radiator, and aluminum driveshaft.
A Roadster Shop stainless fuel tank and Wilwood brakes are fitted to the chassis.

 

Overhead chassis view showing a Tremec manual transmission, aluminum driveshaft, and TIG-welded stainless exhaust routed through frame rails.
The transmission is a Bowler T-56 Magnum. BBT Fabrications built a beautifully routed stainless exhaust system that tucks in snugly, with nothing hanging below the frame.

 

Close-up of dual stainless steel exhaust pipes with V-band electric cutouts passing cleanly through boxed frame ports on a 1967 C10.
Electrically operated exhaust cutouts are fitted, exiting low in the bedsides.

 

Macro detail of a machined stainless exhaust pass-through sleeve welded into the boxed frame rail of a 1967 Chevy C10.
The exhaust cutout passes through a reinforced opening located under the forward bed mount.

 

Parking Brake Cable and Fuel Line Routing on 1967 C10 Frame
The emergency brake cables are cleanly routed around the cutouts.

 

Rear three-quarter view of a patina 1967 Chevy C10 pickup on jack stands showcasing an oval side-exit exhaust tip ahead of the rear wheel.
With the bed installed, you can see how the exhaust cutout exits just in front of the rear tire.

 

Rear view into the cargo bed of a 1967 Chevy C10 displaying a custom raised oak wood floor with stainless bed strips and wheel tub cutouts.
The bed floor was modified to accept the wheeltubs required for the wide rear tires.

 

Fuel-injected LS V8 engine with black intake manifold, tubular headers, and power brake booster fitted inside a patina 1967 Chevy C10.
This “before” view of the engine compartment will be a stark contrast to what comes later.

 

Interior cab view of a 1967 Chevy C10 pickup showing rusted factory floorboards and transmission tunnel before sheetmetal replacement.
The floor of the cab had a good deal of rust, so it was completely replaced with aftermarket panels.

 

Square tubing welded across the door openings of a 1967 Chevy C10 cab to maintain alignment while the rusted floor pan is cut out.
The rear cab panel had rust and dents, which were expertly repaired by the BBT crew.

 

Close-up of severe rust damage along the lower rocker panel and door sill of a 1967 Chevy C10 cab supported on wooden cribbing.
Both doorsill plates were badly rotted, so new metal was shaped to replace them.

 

Macro view of a TIG-welded joint on a new stamped steel rocker panel clamped to a fabrication bench alongside pneumatic grinders.
This is one of the new sill plates under construction.

 

Newly welded and metal-finished steel rocker panel assembly resting on the shop floor ready for installation on a 1967 Chevy C10.
The right-side sill plate is ready to install.

 

Front firewall view of a 1967 Chevy C10 cab on a rotisserie with a new black EDP-coated floor pan and transmission tunnel fitted.
The new floor is being fitted into place.

 

Close-up of the newly installed bare-metal outer rocker panel ground smooth along the door sill of a 1967 Chevy C10 cab.
The new sill plates fit snugly and have been welded into place.

 

Bottom edge of a 1967 Chevy C10 door resting on a work stand showing heavy rust perforation requiring lower skin and shell repair.
The door bottoms also needed repair.

 

Macro view of a TIG-welded lower corner patch panel clamped to a 1967 Chevy C10 door shell during rust repair.
New metal is carefully shaped and fitted into place.

 

Ground and smoothed bare-metal lower door patch panel on a 1967 Chevy C10 door shell before re-skinning the outer edge.
With the door bottom repaired, it is better than new.
Exterior view of a weathered 1967 Chevy C10 door mounted on a work stand with a new bare-metal lower skin patch installed.
The door gaps were adjusted to be laser straight.

 

Inside view of a 1967 Chevy C10 front fender resting on a stand showing severe rust damage at the lower rear heel.
The front fenders had damage that required repair as well.

 

Close-up of a black EDP-coated replacement lower fender patch panel TIG-welded onto a 1967 Chevy C10 front fender.
An aftermarket patch is welded to the lower front edge of the fender.

 

Bare-metal lower fender repair panel ground smooth and contoured to match the factory body line on a 1967 Chevy C10.
With some hammer-and-dolly work and light grinding, the seam disappears.

 

Completed lower front fender rust repair blasted to a uniform satin metal finish beneath the stainless trim on a 1967 C10.
Going over the metal with an orbital sander makes the patch impossible to detect.

 

Custom-fabricated 1967 Chevy C10 frame finished in satin black powder coat resting on jack stands with stainless hardlines nearby.
The chassis has been powdercoated and is ready for assembly.

 

Gloss black tubular upper and lower control arms, coilover shocks, and drilled disc brake hubs laid out on a shop blanket.
All of the suspension and brake components are organized and staged to streamline assembly.

 

Chevrolet orange painted LS V8 engine with classic air cleaner, tubular headers, and Wilwood disc brakes installed in a black 1967 C10 frame.
Thanks to good planning, everything fits perfectly together.

 

Rear three-quarter view of a completed black powder-coated 1967 Chevy C10 rolling chassis featuring Borla stainless mufflers and coilover suspension.
Here you can see how snug all the components fit within the chassis.

 

Satin black aluminum crossflow radiator equipped with dual shrouded electric puller cooling fans resting on a padded workbench.
Twin electric fans have been mounted to the radiator, and everything is finished in satin black.

 

Driver-side engine bay view of a 1967 Chevy C10 showcasing satin black inner fenders, core support, dual electric fans, and Chevy orange LS V8.
The simple color scheme gives the underhood area a very clean appearance. In a future article, you’ll see how this area is taken to the next level of fit and finish.

 

Related Articles

Search Our Site